Fitting Cat Flap in UPVC Door Panel > 문의하기

cat flap in upvc door panel flaps let your pet come and go at their own pace, without you needing to let him in or out. They also help stop your cat from urinating in the house.

Installing a cat flap on a upvc door panel is a lot easier than glass doors, however it requires some knowledge and the right tools.

Take a measurement of the door

Fitting a cat flap in the door isn't easy but if you use the correct type of cat flap make sure you take your time and follow the steps provided it shouldn't be too much trouble. We will show you how to mark out the shape, then use an jigsaw for cutting out the door's area and then finish the job by fixing the cat Flap in upvc door panel flap to the door. This will ensure the flap is in place and shields the doors with cat flap from the damage caused by rain and wind.

The first step is take a measurement of the width of your pet to determine an accurate estimate of what size of cat flap you'll need. This will ensure that the flap is large enough that your pet can enter and leave the house without having to open or close the door every time, but also small enough to stop the pet from straying too far in either direction.

If your kit comes with an illustration of where to drill then you can stick it on the door and then draw a pencil around it. If your door has a moulding or sill on the bottom edge then make sure you have enough clearance from these because this will keep your cat safe and stop them from gaining access to your home.

Put on your eye protection and dust mask, and using a jigsaw start cutting along the line that you've drawn in. Don't push the blade too hard, as this can make it cut faster than you want it to. If you have a set square then use it to check whether you're cutting in the right way and to ensure that the hole is a proper rectangle shape, once you are satisfied with this you can start to remove the remaining door material.

Draw a Line

The cat flap is a great way to let your pet out and in without having to worry about them being a nuisance to a visitor, or leaving unwelcome gifts in the house. It also stops draughts and helps to keep your home's temperature stable. However, installing an animal flap on your door might seem like an intimidating task for those who haven't done it before, leading many people to seek out a professional joiner or carpenter to complete the task. While this is definitely an option, it is possible to do the job yourself if you have the right tools and follow the instructions with care.

This is much easier to do on wooden doors, but it is still possible using uPVC. However you should be cautious not to harm the doors as this could invalidate your guarantee. The first step in the process is to measure the door and ensure that it is able to fit the new cat flap. This should be simple enough if you are using the standard uPVC door, however you may need to take extra care if you are using an alternative type of door as these can be more difficult to cut than solid uPVC panels.

The next step is to determine the height of your cat flap installer's belly. This is the amount of height between the floor and the bottom of your cat's stomach. It is important to locate an area at the entrance that will allow your pet to move through easily. Once you have the information you'll have to mark the area with a spirit-level and a pencil so you know the opening will fit your cat.

Once you've marked the area, it's time to make the hole. You will require the jigsaw, and it is important that you take your time to ensure that the cuts are smooth and straight rather than rough and uneven, as it could cause damage to your door. Be sure to wear safety glasses and a dust protection mask at all times when working with the jigsaw as inhaling the sawdust could be harmful to your health. After you've completed the cutting, you'll have to smooth the edges of the hole using sandpaper, so that your cat flap in upvc door panel flap will fit easily into place.

Make a hole

It can be difficult to put the cat flap onto the door panel or double glazing unit. You might be tempted to do it yourself, but unless have expertise in DIY, it's probably best to get a professional in to do the job for you. A botched job could not only be unsightly, but also pose an security risk. It could allow cold air in when the cat is outside and cat flap in upvc door panel hot air out when inside.

The hole's location should be marked on the door using a pencil and spirit level. This will ensure it is positioned correctly and is flush with the door's other parts. Make sure to have sandpaper to smooth out any rough edges.

Wear the safety equipment you'll need to use the power tool. If you are concerned about the noise of a jigsaw you can buy one that is cordless, which is quieter and simpler to use.

You should only remove the material required to create the cat flap. A little bit of extra material is required to increase the thickness of the wall of the flap, but cutting off more than this can cause problems and even cause damage to the door frame.

If the upvc door is made of metal, or has a frame, it may interfere with the microchip flap. In this scenario you'll need to create an over-sized hole to ensure that the metal does not get in contact with the wall of the flap.

If you are fitting a cat flap into the frame of a double glazed window with a frame made of metal, you'll need to speak to a specialist who can supply you with a new glass pane with the hole for the cat flap already drilled inside. It is much less expensive to have this done than trying to fix the cat flap onto an existing pane of glass that hasn't been designed specifically for this purpose.

Install the Flap

Cat flaps allow your pet to move around at their own pace, giving them the freedom to relax in the home whenever they want to. If you have an uPVC front door, it may be difficult to install the cat flap. This is especially true if you do not own a glass panel that can be cut. Luckily, if you're happy to purchase and install a new half-glazed uPVC panel then it is possible to add an animal flap onto these doors. It's not as simple as cutting a hole in the door though and there are a few things you'll need first to make sure it's safe.

A composite, upvc door panels with cat flap, or GRP door panel typically comprises an flimsy plastic outer layer that is bonded to a soft, polystyrene insulating core. The material is extremely fragile and care must be taken when cutting through it to avoid causing damage. This type of door typically includes a template which you can use as a guide for cutting the hole in your door.

After you have marked out the hole in your front door, it's time to put in the cat flap. You can purchase and install a wide variety of different models, from basic push-button operated models to microchip activated units that allow only your pet. But, regardless of the kind of cat flap you choose it's crucial to ensure that your cat is able to use the flap without getting trapped outside in bad weather.

A circular fitting is better than a square, because circles can be cut more securely into the glass. This is because square holes are more likely to break the glass when they are drilled. This is also a safer option, as you won't have to drill into the toughened glass, which could break and cause harm to your pet or family members. This is particularly important if you have child or an elderly person living in your home who may be hurt by shards of glass.