8 Tips To Increase Your Kia Picanto Key Fob Replacement Game > 문의하기

How to Replace a Kia Sportage Replacement Key

For many Kia models the key comes with a keyless entry system built-in. The key can be compared to an remote control, and is able to be replaced with a fresh one from an Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including an empty coin battery worn buttons signal interference, water damage and a malfunctioning receiver module. Here are some suggestions on how to get your Kia Sportage replacement key working again.

How do you replace a smartkey or remote key?

The battery in your kia forte key fob's intelligent key will eventually have to be replaced, regardless of whether it is a remote key that starts with a push button or a normal metal key that doesn't have a transponder. This is particularly when your car displays a message that indicates the remote or smart keys aren't powered.

It's quite simple to do. To replace the battery of the key fob remove the mechanical key from the slit at the back of the key fob. Then lift the cover. A small screw will be located inside the key fob that holds the battery in the correct position. By using a small screwdriver take the screw off and pull out the old battery. Insert the new battery and then close the gap on the key fob.

Once the key fob has an updated battery Test it by pressing the locks and unlock buttons. If the doors unlock and lock exactly as you expect, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia when your fingers get chilly or when you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a programming machine that is available only to the locksmith for cars or dealer. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, you'll need note the key code number on the tag for the key code.

How do I replace the battery?

If the Kia key fob is unable to respond to pressing the lock/unlock button, it is most likely that the battery is not fully charged. A battery that is not functioning properly could cause other issues like the check engine light flashing on or delayed engine cranking. Fortunately, replacing the battery on the key fob is a relatively easy DIY project that requires only the most basic tools.

Before you begin before beginning the process, ensure that your vehicle is turned off and that all doors are shut. Find the small metal or a plastic piece at the bottom of the key fob. Then, jiggle it until the metal key pops out. This key can be inserted into the driver door handle to unlock your car.

To replace the key fob battery, remove the cover from the back and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery, and then align the new battery to ensure that the "+" positive side is facing you, and the "-" negative side is facing the fob's metal electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

Once the new battery has been installed, turn the key fob off and then on in the ignition until the door locks cycle. You can then test your 2016 kia soul replacement key's keys fob again to confirm that it's working as intended.

How do you replace the smart key

You may have either a standard keyfob, or a Smart Key based on the model of Kia Sportage. The difference between these is that the smart fob has a small mechanical key blade in it, whereas the standard fob doesn't. Both key fobs are equipped with batteries that eventually require changing. Luckily, this is a fairly simple process that takes only two minutes.

Before you begin before you begin, ensure that you're on a level surface with adequate lighting and that your Kia is turned off. Also, remember that there are small parts inside the fob that could fall out if not vigilant.

The first step is to locate the small release button that is located on the backside of the fob. It's either an oval or circular slot. When you press it, the mechanical key blade will be released and you will be able to open the key fob.

Once the key fob is removed, you can remove the battery that was in it. The new battery is a CR-2032, and can be purchased through the internet or at a local auto parts store. After you're done, your key fob should permit you to lock and unlock your vehicle, even if it isn't running.

How do I replace the mechanical key?

The Kia key fob is a great option that lets us lock and unlock our car at the touch of an button. But, as with all devices, it can have problems from time to time. Luckily, there are methods to resolve these issues and ensure that our key fobs are in good condition for the long run.

A dead or weak battery is one of the most frequently encountered issues. This can cause your fob to stop working or operate intermittently. If this is what you are experiencing it is time to replace the battery a new one.

If this does not resolve the issue, try using the flathead screwdriver that is standard to wedge the fob's casing made of plastic open. Be careful not to scratch any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the fob to make sure it's functioning correctly. Contact a dealer or locksmith to address the issue in the event that the fob is not working. To avoid future lockouts, ensure you have an emergency key that will work on all trunk and door cylinders.