What's The Ugly Truth About Car Ignition Lock > 문의하기

Why is My Car Ignition Locked?

There are several reasons why your ignition in your car may be locked. One reason is that the key is dirty or has a damaged wafer inside. You can fix it by sliding the key into and out of the cylinder several times.

Another possibility is that the pins in the lock cylinder have become stuck. You could tap the cylinder lightly with a small tack-hammer.

Check the Battery

The transmission shifter switch may be malfunctioning if the vehicle is in Park neutral, or doesn't start when the key is switched on. This can be easily solved by moving the switch up or down to get the car in the correct gear.

If the car doesn't turn, the issue could be related to the neutral safety cable or the shifter on the transmission. A mechanic or a local auto locksmith ignition replacement locksmith can fix these issues.

The ignition cylinder could also be worn out. Over time, the ignition and the key can wear out, causing them to become difficult to insert or remove. A lubricant like silicon lock grease could solve this issue, letting the wafers to slide into place.

The key can become clogged by lint from your pockets as well as adhesive from tape used to secure packages. This prevents the key from sliding into the ignition. To solve this problem, you can try cleaning the key using the help of a cloth or a cleaner, such as Triflow. You may also try a spare key to determine if the issue is the key or ignition.

When the key is in the ignition you can tap it using a an hammer that is small. This can cause a small vibration that may be enough to loosen the wafers inside the ignition, allowing them to slide into position. Be careful not to damage either the ignition cylinder or the key.

If none of the suggestions above work, you need to consult a locksmith for help in figuring it out. It could be that the key is damaged inside the ignition or it could be the time to replace the entire thing. If the issue is with the key, a locksmith will be able to create a new key for you. If the issue is with the ignition cylinder, the vehicle must be taken to a repair shop to get it replaced. These problems are usually easy to solve.

Examine the Steering Wheel

A simple issue that could hinder the ignition from turning is a locked steering wheel. This happens if the driver is unable to engage it when they exit or enter the vehicle. It is typically caused by pulling on the wheel and securing themselves against it with their hands. It could also happen when a passenger in the rear seat is unable to stop the vehicle and engages the brakes when they get out of the vehicle.

Luckily it's an easy fix that doesn't require a trip to an expert locksmith or mechanic. First, ensure that the gear shift is either in Neutral or Park. If it's not then gently pull or push the gear shifter until it shifts to one of these positions. It is also essential to press the brake or activate the handbrake before you attempt to turn the key.

If the wheel isn't locked, a quick inspection of the steering column will reveal if the key is engaged with the lock cylinder. A small "Lock label can be located in the lower part of the ignition circle. It is possible to disengage the lock by gently jiggling it or pulling it back with moderate force. It is important not to apply too much force, as it could damage the key or cut off a wafer within the lock cylinder.

Another option is using a spare key to see if it can disengage the lock. This could indicate that the original key has damaged and no more able to engage the wafers inside the lock cylinder. If this is the case the locksmith at Karl Chevrolet Webster City will be able to create an alternative key.

If the key still doesn't engage after spraying the penetrating lubricant it could help. Apply a small amount penetrating oil to the ignition key replacement and keyhole. Then, jiggle it or tap it lightly to get it working. If this doesn't work, you may need to speak with a specialist at your local dealership for cars. They'll be able provide you with a replacement key and also replace the ignition cylinder in the event that it is required.

Check the Key

It is possible that your key is damaged if it will not turn on. You can get rid of any foreign material (lint from packing tape or adhesive) from the key. You should also try rubbing alcohol or Goo Gone on the key to see if it aids.

If the pins inside the lock aren't moving correctly when you insert your key, it's possible that they are stuck. If you have an extra key to test, you can try placing it into the ignition and gently sliding it back out. You should be in a position to feel and hear the pins moving inside. If you don't hear or feel any movement, you can lubricate them with graphite powder. You can purchase graphite in small tubes that can be applied directly to the keyhole. This will assist the pins slide into place when you insert the key, and will prevent them from getting stuck.

It is possible that your key has worn out or damaged and isn't able to connect with the pins in the ignition cylinder. This could cause the cylinder to stop to turn, preventing you from starting your car. If this is the case you'll need to take your vehicle to repair ignition lock cylinder or locksmith shop for repair.

If you're able to turn the car with a spare key and you've ruled out issues with the steering wheel or battery, it could be that the ignition cylinder is worn out. You can try to loosen the lock cylinder using the sharp end of a screwdriver or handle of a Hammer (not the head). Gently tapping on the cylinder will usually free it which allows you to turn your key and start your vehicle. If this is not working then you'll need to replace the lock cylinder by an expert mechanic.

Check the Ignition Socket

The ignition socket is where your key is inserted and slides out of position when it is inserted. It could get blocked with dust, or simply wear and wear and tear. Try putting some silicon lock lubricant (like WD-40) into the ignition to help things move along.

You can also use a small hammer and tap gently on the inside of the ignition to try to loosen or reset the pins that are not aligned. Again, be very careful not to overdo this, or you could cause serious damage to the ignition switch.

Before you attempt this, make sure that the car's gearbox is set to neutral or park. Many modern cars have the ability to stop the steering wheel from turning when it is not in neutral or park and prevent the key from being turned into the ignition.

If you've tried all of this but can't get your key to turn it is likely that the ignition cylinder housing is in need of replacement. Different vehicles have different methods for replacing the ignition cylinder, so it is important to follow the correct procedures.

Generally speaking, this involves removing the plastic cover that is over the steering column and ignition assembly. To remove it, you'll have to adjust the tilt-wheel in its lowest position. Then unscrew any fasteners holding it in place.

After removing the cover you'll have to remove the old ignition cylinder from the steering column. Then, you'll need to compare the new ignition cylinder you purchased with the one you removed to confirm that they are the same. Once this step is complete the new ignition cylinder is able to be installed in the same way that the old one was removed.

It is possible that even with our best efforts, the ignition may become damaged and need to be replaced. If this happens, it's advised to contact an Tempe Locksmith for assistance. A locksmith can assist you determine the correct replacement and ensure it is installed correctly to ensure that your vehicle will restart.